scanning velocity造句
例句與造句
- Application of scanning velocity modulation circuit in digitalized color tv receiver
掃描速度調制電路在數字化彩電中的應用 - Calibration of scanning time and scanning velocity for high speed image - converter camera
高速變像管相機掃描時間和掃描速度的標定技術 - Then the key process parameters of laser bonding , including laser power , scanning velocity , and initial temperature , are obtained with the help of scanning experiments
運用該模型計算了不同的工藝參數條件下硅玻璃的溫度場分布，并由此得出鍵合線寬。 - Moreover , it showed that the linearity rising relations were existed between the laser power and the thickness of hardening layer , and the linearity negative rising relations between the scanning velocity and peak rigidity
此外，結果還表明激光功率與淬硬層厚度成線性增長，而掃描速度與峰值硬度成線性負增長關系。 - ( 4 ) based on the mechanism of sls ( selected laser sintering ) , a matching rule between scanning velocity and laser power is established so as to realize the laser power matching in different scanning velocities
( 4 )從激光選擇性燒結機理出發，建立了激光掃描功率與掃描速度之間的匹配規則，以實現在不同掃描速度下激光功率的自動匹配。 - It's difficult to find scanning velocity in a sentence. 用scanning velocity造句挺難的
- Groove shape function of laser power , scanning velocity and materials ' thermo physical coefficients was solved due to temperature at ablation front keeping decomposed temperature , and the proposed model was tested in polymethylmethacrylate experiment
基于燒蝕面上的溫度始終保持為降解溫度，求出關于激光功率、掃描速度和材料熱物理系數的微流道外形函數解，并用聚甲基丙烯酸甲酯進行了實驗驗證。 - The paper studied actual method of imc about panoramic aerial camera , and put forward a true _ angle imc method in scanning orientation . the true _ angle imc is independent of scanning velocity , and the demand of drum control system ' s rotational velocity ' s precision is reduced . at last , through experiments , the true _ angle imc was validated
研究了全景相機像移補償?shù)木唧w實現方法，提出了相機在擺掃方向上的真角度補償方法，補償后的像移誤差與擺掃速度無關，從而降低了對鏡筒掃描系統的穩速精度要求。 - The optimal parameters of making high silicon content aluminum alloys is : spray height is 220 - 230mm , spray angle is 30 ? the scanning velocity of atomizer is 30mm / s , the original offset of the substrate is 30mm , rotation velocity of the substrate is 120rpm , spray gas pressure is l . ompa , the diameter of the delivery tube is 3 . 6mm , the drawing velocity of the substrate will be adjusted on - line with a plc on the basis of the spray
通過對多層噴射沉積原理及工藝參數的研究，得出制備al - 22si - 3cu - 1mg合金的最佳工藝參數為：噴射高度為220mm - 230mm ，基底轉速為120rpm ，霧化器掃描速度為30mm / s ，基底下降轉速依據噴射情況由智能控制器進行實時調整，噴射角度為30 ，初始偏心距為30mm ，導流管直徑為3 . 6mm ，霧化氣壓為1 . 0mpa 。 - As the vital development of the millimeter wave guidance technology , phased array antennas use electrical control scanning beam , which results to faster scanning velocity , more flexible beam control and higher anti - interference ability . thus it can realize target seeking , tracing , guidance at the same time , and can work in the complex and worsening condition
作為毫米波制導技術的一個重要發展方向,相控陣制導技術中的相控陣天線是采用電控方式掃描波束,掃描速度快、波束控制靈活、抗干擾能力強等,可以同時完成目標搜索、跟蹤、引導等多項功能,能工作在日益復雜和惡化的工作環境中。